Fortec 5680-BD Kevlar
Kevlar fiber bi-directional fabric for crack repair, water-proofing and structural reinforcement
|
 |
Fortec 5680-BD Kevlar is a bi-directional fabric system comprised of highly durable 5,680 denier Kevlar yarns, producing a superior and dense weave. The system is designed for heavy duty crack repair, crack control, and structural strengthening of concrete and masonry structures where durability, impact resistance and protection of water intrusion is needed. The system of Fortec 5680-BD Kevlar textile used with Fortec Lo-Mod 526 Flexible epoxy resin is the best alliance of strength and bonding that seals out moisture, transfers loads and allows temperature and stress related movements to occur without brittleness.m.
Key Features
- 0o and 90o, equal bi-directional strength
- High bond strength
- Conforms to irregular surfaces
- Easy gun-applied epoxy resins
- Strongest duty Kevlar® system available
- Excellent crack control
| |
|
Fortec Carbon Tow Sheet
Unidirectional Carbon Fiber Textile or Tow Sheet for structural reinforcement and containment
Available in 150, 300, 600 and 700 GSM
|
 |
Fortec Carbon Tow Sheet is a flexible, woven, unidirectional carbon fiber textile with a lightweight scrim on both sides designed for use as an externally applied reinforcement for strengthening concrete, timber and masonry structures. Fortec Carbon Tow Sheets are typically field installed using either Fortec #4550 LPL or #1276 LPL Hi-Modulus Fiber Matrix epoxy resins to form an inexpensive carbon fiber reinforced polymer (CFRP) system.
Key Features
- Reinforcement & strengthening of irregular shapes
- Column wrapping
- Cantilever retaining wall reinforcing
- Supplementary reinforcing of beams & slabs
- Inert reinforcement in highly corrosive environments
| |
|
Fortec Carbon Bars
Carbon fiber reinforced polymer (CFRP) rods (rebar) for structural reinforcement
|
 |
Fortec Carbon Bars are pultruded carbon fiber reinforced polymer (CFRP) rods or bars for structural reinforcement. They are designed for strengthening concrete, timber and masonry structures and usually used with the Near Surface Mounted (NSM) installation technique. Bars are inserted into grooves cut into the substrate and bonded with an epoxy resin. The bars can also be used as original reinforcement for these structures and used for mechanical connection of Fortec CFRP fabrics on substrates where additional anchorage is desired.
Key Features
- Fast installation time
- No substrate surface preparation required
- Simple groove installation
- Easy gun-applied epoxy resins
- Protected via recessed installation
- Better fire resistance
| |
|
Fortec Carbon Plate System
Unidirectional Carbon Fiber Plate for structural reinforcement and containment
|
 |
Fortec Carbon Plate System is a unidirectional, pre-impregnated, carbon fiber reinforced polymer (CFRP) comprised of high tensile strength and high modulus carbon fibers encapsulated in a thermal set resin and cured under pressure during the manufacturing process and designed for use as an externally applied reinforcement for strengthening concrete, timber and masonry structures. A peel-ply fabric is adhered to the plate and when removed leaves a prepared bonding surface for adhesion to a prepared substrate. Fortec Carbon plates and CFRP plates can be manufactured for various modulus and tensile strengths as well as bidirectional systems. Fortec Carbon Plate System are typically field installed using Fortec #4020 Epoxy Gel.
|
Key Features
- Designed for use in lieu of multiple layers/plys of fabric
- Supplementary reinforcing of beams & slabs
- Inert reinforcement in highly corrosive environments
|
 MORE INFORMATION
| |
|
Fortec 6K-BD Strap
Carbon fiber bi-directional grid for crack control and structural reinforcement
|
 |
Fortec 6K-BD Strap is a 100% carbon fiber, bi-directional grid system comprised of high strength, 6K carbon fiber tows. The system is designed for crack sealing, crack control and structural strengthening of concrete and masonry structures where a thin and highly durable finish is desired. The strap system seals and transfers loads over cracks caused by shrinkage and thermal contraction, joint seal failure, load stress, settling, movement and age. The 6K-BD strap is saturated in a high bond, high strength epoxy resin on a prepared substrate to complete the system.
|
Key Features
- 0o and 90o, bi-directional strength
- Hi bond strength
- Conforms to irregular surfaces
- Easy gun-applied epoxy resins
- Thinnest strap system available
- Excellent crack control
|
MORE INFORMATION
| |
|
Fortec #4550 LPL Structural Epoxy
Moisture insensitive, high modulus, high strength, structural epoxy resin
|
 |
Fortec 4550 LPL Hi-Modulus Fiber Matrix is a 100% solids, solvent-free, two-component MOISTURE INSENSITIVE EPOXY.
Fortec 4550 Fiber Matrix is a low viscosity epoxy for wetting and use with carbon fiber for structural repairs.
ADVANTAGES
- Easy mix ratio: 2 Parts A to 1 Part B by Volume
- Long Pot Life with rapid strength development
- Provides high early strength and excellent adhesion to most structural materials
- Insensitive to moisture before, during and after cure
- Low temperature cures - As low as 40oF (4oC)
PHYSICAL PROPERTIES
- Moisture Insensitive & low temperature cure
- #4550 LPL Fiber Matrix Structural Epoxy
| |
|
Fortec Epoxies and Resins
Moisture insensitive, high modulus, high strength, structural epoxy resins
|
ForTec #4124 Epoxy Resin & Hardener.
The 4124 Epoxy system is formulated for laminating synthetic composite structures. Use 4124 for primary laminating applications and for tabbing, taping and secondary
bonding applications. The 4124 will provide a working time of approximately 30 minutes at 72o F. A typical laminate will be gelled in approximately 2 hours at 72o F. | |
|
ForTec #590 Superstick Hi-Mod Gel.
ForTec 590 HI-MOD GEL is a 100% solids, solvent-free, two-component MOISTURE INSENSITIVE epoxy structural adhesive system. It has a unique HI-MODULUS OF ELASTICITY. When mixed with salt-free kiln-dried silica aggregate, 590 will produce a sag-resistant mortar for both vertical and overhead patching of interior surfaces. ForTec 590's gel-like consistency is an excellent structural adhesive for bonding of mating or non-mating surfaces. 590 Gel is recommended to grout anchor bolts, to seal cracks, and to set injection ports prior to injection grouting.
| |
|
ForTec #105 Epoxy Coating System
Fortec 105 superstick Hi-Build is a 2 component epoxy resin based coating which is Solvent-Free, 100% Solids and 100% Reactive. Superstick Hi-Build is a "tile like" high build protective coating providing a corrosion resistance, damp-proofing waterproofing vapor barrier system for concrete masonry concrete block, brick, etc. ANSI /NSF 61-1992 approved for Potable Water Use.
| |
|
ForTec #4020 Hardened Hi Modulus Eposy Gel
The gel and cure times are affected by ambient temperature and epoxy mass,or glue line thickness. Curing data is based on 72oF (22oC) ambient temperature
| |
|
|
CONTRACTOR SUBMITTAL PACKET. Announcing the Fortress/Fortec Installer Bid Package: We've been working with Richard E. Prince, PE of Prince Engineering PLC in Traverse City MI and we have developed a tool to help you in qualifying for DOT and Commercial projects. (25 pages, 1.2 MB. PDF format)
|
|
|
PRODUCT SPECIFICATIONS: